لیست بخشی از آزمون های قابل ارائه توسط آزمایشگاه شرکت نفت ری سان به شرح ذیل می باشد:
| ردیف | عنوان آزمون | استاندارد |
| 1 | PH (100% vol) of Engine Coolants | ASTM D 1287 |
| 2 | PH (50% vol) of Engine Coolants | ASTM D 1287 |
| 3 | Freezing Point of Engine Coolants- °C | ASTM D 1177 |
| 4 | Boiling Point of Engine Coolants (100% vol) -°C | ASTM D 1120 |
| 5 | Boiling Point of Engine Coolants (50% vol) -°C | ASTM D 1120 |
| 6 | Foaming Tendencies of Engine Coolants in Glassware-ml/s | ASTM D 1881 |
| 7 | Corrosion Test for Engine Coolants in Glassware-mg | ASTM D 1384 |
| 8 | %Percent Ash Content of Engine Coolants -wt | ASTM D 1119 |
| 9 | Water in Engine Coolant by the Karl Fischer-ppm | ASTM D 1123 |
| 10 | Reserve Alkalinity of Engine Coolants-ml | ASTM D 1121 |
| 11 | Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles | ASTM D 1882 |
| 12 | Appearance | Visual |
| Visual | ||
| 13 | Color of Petroleum Products | ASTM D 1500 |
| 14 | Kin.Viscosity of Petroleum Products at 100°C - cSt | ASTM D 445 |
| 15 | Kin.Viscosity of Petroleum Products at 40°C - cSt | ASTM D 445 |
| 16 | Viscosity Index | ASTM D 2270 |
| 17 | Kin. Vis.@100°C - cSt after shear | ASTM D 6278 |
| 18 | Kin. Vis.@100°C - cSt after shear | ASTM D 6278 |
| 19 | Flash Points by Cleveland Open Cup Tester - °C | ASTM D 92 |
| 20 | Pour Point of Petroleum Products -°C | ASTM D 97 |
| 21 | Density of Crude Petroleum and Liquid Petroleum Products by Hydrometer at 15/5°C -Kg/m3 | ASTM D 1298 |
| 22 | Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel (RPVOT) - min | ASTM D 2272 |
| 23 | Oxidation Stability of Gasoline Automotive Engine Oils by Thin-Film Oxygen Uptake (TFOUT)-min | ASTM D 4742 |
| 24 | %Evaporation Loss of Lubricating Oils by the Noack Method (A) -wt | ASTM D 5800 |
| 25 | %Ash from Petroleum Products -wt | ASTM D 482 |
| 26 | %Sulfated Ash from Lubricating Oils and Additives-wt | ASTM D 874 |
| 27 | Determination of demulsibility characteristics of lubricating oil | IP-19 |
| 28 | Water Separability of Petroleum Oils and Synthetic Fluids-ml/ml/ml/min | ASTM D 1401 |
| 29 | Water Separability of Petroleum Oils and Synthetic Fluids-ml/ml/ml/min | ASTM D 1401 |
| 30 | Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer-CP | ASTM D 2983 |
| 31 | Apparent Viscosity of Engine Oils and Base Stocks Between –5 °C &–35 °C Using Cold-Cranking Simulator (CCS) -cP | ASTM D 5293 |
| 32 | Foaming Characteristics of Lubricating Oils-ml/s | ASTM D 892 |
| 33 | Rust-Preventing of Oil in the Presence of Water | ASTM D 665 |
| 34 | Rust-Preventing of Oil in the Presence of Sea Water | ASTM D 665 |
| 35 | Copper Corrosion | ASTM D 130 |
| 36 | Determination of Water in Oils by Karl Fischer-PPm | ASTM D 6304 |
| 37 | Acid Number of Petroleum Products by Potentiometric Titration(TAN) -mgKOH/g | ASTM D 664 |
| 38 | Base number- Percholoric acid petentiometric(TBN) -mg KOH/g | ASTM D 2896 |
| 39 | Elemental analysis-ppm | ASTM D 6595 |
| 40 | Air Release of Oils | ASTM D 3427 |
| 41 | Particle counter | NAS 1638 |
| 42 | TDS of water | ASTM D 5907 |
| 43 | Copper Corrosion from Lubricating Grease | ASTM D 4048 |
| 44 | Worked Peneteration | ASTM D 217 |
| 45 | Unworked Peneteration | ASTM D 217 |
| 46 | Shear Stability @ 30 Cycle | ASTM D 6278 |
| 47 | Shear Stability @ 90 Cycle | ASTM D 6278 |
| 48 | Shear Stability @ 120 Cycle | ASTM D 6278 |
| 49 | FT-IR | ASTM E 168 |
| 50 | High Temperature Foaming Characteristics of Lubricating Oil | ASTM D 6082 |
| 51 | MRV- Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature | ASTM D 4684 |
| 52 | HTHS-Measuring Viscosity at High Temperature and High Shear Rate by Tapered-Plug Viscometer | ASTM D 4741 |
| 53 | FT-IR Spectrometers for In-Service OCM-Oxidation | ASTM D 7418 |
| 54 | FT-IR Spectrometers for In-Service OCM- Nitration | ASTM D 7418 |
| 55 | FT-IR Spectrometers for In-Service OCM- Sulfation | ASTM D 7418 |
| 56 | Water in Oil | Crackel |
| 57 | Oxidation Stability of Lubricating Greases by the Oxygen Pressure Vessel Method | ASTM D 942 |
| 58 | Dropping Point of Lubricating Grease | ASTM D 2265 |
| 59 | Thermo-oxidation Engine Oil Simulation Test– TEOST 33C | ASTM D 6335 |
| 60 | Thermo-oxidation Engine Oil Simulation Test – TEOST MHT | ASTM D 7097 |
